ANYCUBIC PLA 3D Printer Filament, Glow in The Dark, 3D Printing PLA Filament 1.75mm Dimensional Accuracy +/- 0.02mm, 1KG Reusable Spool (2.2 lbs), Green PLA, Glow Green

Product Details

• 【𝐆𝐥𝐨𝐰 𝐢𝐧 𝐭𝐡𝐞 𝐃𝐚𝐫𝐤】lt contains fluorescent materials that can glow in the dark after absorbing light energy. Compared to similar products on the market, Anycubic Glow-in-the-dark PLA Filament has a brightness increase of 300% and a 150% increase in glow duration under the same lighting conditions. We recommend you to expose the prints to a full of sunlight or UV light for a period of time.
• 【𝐀𝐜𝐜𝐮𝐫𝐚𝐜𝐲 & 𝐂𝐨𝐧𝐬𝐢𝐬𝐭𝐞𝐧𝐜𝐲】 Anycubic 3D Printer PLA filament of 1.75mm diameter, Minimum dimensional tolerance +/- 0.02mm, which makes filament outflow smoother, came out homogeneous. The low shrinkage and stable printing dimensions make the fusion between the layers very good to obtain an even better-bridging result. You don't worry the diameter changes a lot then the feed rate is disrupted with thicker and thinner layers at all.
• 【𝐍𝐞𝐚𝐭 𝐒𝐩𝐨𝐨𝐥 & 𝐏𝐫𝐞𝐦𝐢𝐮𝐦 𝐐𝐮𝐚𝐥𝐢𝐭𝐲】 The 3D Printing PLA filament was neat on the roll and easily left the spool without crossing turns. Resulting in less thread pulling and twisting, no clogging, and super under-extruding. It produces the cleanest, least stringing prints of any of the filaments you have used while resisting warping and providing the glossiest finish. Without a single jam and adhesion issue which meets your demands for printing freely.
• 【𝐂𝐥𝐨𝐠-𝐅𝐫𝐞𝐞 & 𝐁𝐮𝐛𝐛𝐥𝐞-𝐅𝐫𝐞𝐞】 Designed and Manufactured with a Clog-Free to ensure a smooth and stable printing experience with our PLA refills. Completely dried for 24 hours before packaging and vacuum sealed with desiccants in nylon re-bag enable much smoother and more stable printing. The larger spool inner diameter design makes feeding smoother.
• 【𝐅𝐢𝐥𝐚𝐦𝐞𝐧𝐭 𝐈𝐧𝐬𝐭𝐚𝐥𝐥𝐚𝐭𝐢𝐨𝐧】 1. Install the spool on the spool holder of a 3D printer, and preheat the nozzle of the 3D printer. 2. Cut the filament tip diagonally, and guide it through the extruder and feeding tube. 3. Manually push the filament through the feeding tube to the nozzle, until the filament melts through the nozzle. Note: When installing and changing filament, we highly suggest preheating the nozzle first to reduce the nozzle block risk.

From the listing on Amazon.

View our other ANYCUBIC listings here.

View our other PLA listings here.

Keep your filament dry, view our gear here.

Printing ANYCUBIC PLA

ANYCUBIC PLA in Glow Green runs on the PLA profile below, and this listing is a 1kg spool. PLA is best suited to everyday prototypes, models, and indoor parts that won't face heat or heavy stress. Brands and even individual spools vary, so treat these as starting points and run a quick temperature tower to lock in the sweet spot for your printer.

Ranges checked against Bambu Lab, Prusament and Polymaker data. Heat resistance is the heat deflection temperature (HDT). Read our PLA filament guide for bed adhesion, drying, troubleshooting, and material-specific tips.

Nozzle Compatibility

This listing includes glow-in-the-dark filament. The phosphorescent pigment that makes it glow is hard and wears brass nozzles quickly, even though the filament looks like ordinary plastic. Use hardened steel or another wear resistant nozzle, starting about 5 to 10°C hotter than with brass.

Based on Bambu Lab, Polymaker and eSUN guidance. More in our nozzle types guide.